View 293D107X0010D2T_49440.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

293D
Vishay Sprague
Solid Tantalum Chip Capacitors TANTAMOUNT(R), Commercial, Surface Mount
FEATURES
* Molded case available in six case codes. * Compatible with "High Volume" automatic pick and place equipment. * Optical character recognition qualified. * Meets IEC Specification QC300801/US0001 and EIA 535BAAC.
PERFORMANCE/ELECTRICAL CHARACTERISTICS
Operating Temperature: - 55C to + 85C. (to + 125C with voltage derating.) Capacitance Range: 0.10F to 680F. Capacitance Tolerance: 20%, 10% standard. (20% only on P) Compliant Terminations 100% Surge Current Tested (D & E Case Codes). Voltage Rating: 4 WVDC to 50 WVDC.
OTHER SPECIFCATIONS
CECC 30801-005 30801-009 30801-011 30801-801 793DX CTC3 CTC4 793DE IECQ PQC32/GB003 300801/FR001 793DX CTC3
ORDERING INFORMATION
293D TYPE 793DX 793DE CTC3 CTC4 107 CAPACITANCE X9 CAPACITANCE TOLERANCE 010 DC VOLTAGE RATING @ + 85C D CASE CODE See Ratings and Case Code Tables. 2 TERMINATION 2 = Solderable coating. Standard. W REEL SIZE AND PACKAGING T = 7" [178mm] reel,* W = 13" [330mm] reel* *cathode nearest sprocket hole.
This is expressed in X0 = 20% This is expressed in volts. picofarads. The To complete the threeX9 = 10% digit block, zeros precede first two digits are X5 = 5% the significant the voltage rating. A figures. The third is (Special Order) decimal point is indicated the number of zeros by an "R" to follow. (6R3 = 6.3 volts). Note: Preferred Tolerance and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
L
H TH Min.
W
TW
P
CASE CODE A B C D E P
EIA SIZE 3216 3528 6032 7343 7343H 2012
L 0.126 0.008 [3.2 0.20] 0.138 0.008 [3.5 0.20] 0.236 0.012 [6.0 0.30] 0.287 0.012 [7.3 0.30] 0.287 0.012 [7.3 0.30] 0.079 0.20 [2.0 0.008]
W 0.063 0.008 [1.6 0.20] 0.110 0.008 [2.8 0.20] 0.126 0.012 [3.2 0.30] 0.170 0.012 [4.3 0.30] 0.170 0.012 [4.3 0.30 0.049 0.008 [1.25 0.2]
H 0.063 0.008 [1.6 0.20] 0.075 0.008 [1.9 0.20] 0.098 0.012 [2.5 0.30] 0.110 0.012 [2.8 0.30] 0.158 0.012 [4.0 0.30] 0.047 Max. [1.2 Max.]
P 0.031 0.012 [0.80 0.30] 0.031 0.012 [0.80 0.30] 0.051 0.012 [1.3 0.30] 0.051 0.012 [1.3 0.30] 0.051 0.012 [1.3 0.30] 0.020 0.008 [0.52 0.20]
TW 0.047 0.004 [1.2 0.10] 0.087 0.004 [2.2 0.10] 0.087 0.004 [2.2 0.10] 0.095 0.004 [2.4 0.10] 0.095 0.004 [2.4 0.10] 0.047 0.004 [1.2 0.10]
TH (Min.) 0.028 [0.70] 0.028 [0.70] 0.039 [1.0] 0.039 [1.0] 0.039 [1.0] 0.012 [0.3] www.vishay.com 15
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
293D
Vishay Sprague
RATINGS AND CASE CODES
4V 6.3 V Ext. Std. Ext. 10 V Std. Ext. 16 V Std. Ext. 20 V Std. Ext. 25 V Std. Ext. 35 V Std. A A A A B B B C C C D D D Ext. 50 V Std. A B B B B/C C C D D D Ext. A A A A B B C C/D C D/E D/E
F
0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680
Std.
P
A A A A/B/P B/P B/C/P C C D D D E
A A A/B A*/B B/C B/C B/C C/D D/E D/E E
A A/P A/B/P A/B/P B/C/P B/C C C D D D E
A A A/B A/B B/C B/C B/C C/D D/E D/E E
A A/P A/P A/B/P B B/C C C D D D
A A A/B A/B B/C B/C B*/C C/D D/E D/E E
A/P A A/B A/B B B/C C C D D D
A A A/B B B/C B/C C D D/E D*/E
A A A B B B/C C C D D D
A A A B B B/C C C D/E D/E E
A A B B B C C C D D
A A A B B B C C D D/E E*
A A A B B B C C C D/E D/E E*
*Preliminary values, contact factory for availability.
CONSTRUCTION AND MARKING
CONSTRUCTION MARKING Capacitance Code, pF Vishay Sprague Logo "A" Case Polarity Band Capacitance Polarity Band B, C, D, E Voltage
V 104
22 XX
Date Code Volts
10 2
Vishay Sprague Logo Code
G J A C D E V T
Cathode Termination ( - ) Polarity Stripe (+) Epoxy Case
Voltage Code
X
Tantalum Capacitor Element Anode Weld Positive Termination Voltage
X
"P" Case Polarity Band
Capacitance
4 6.3 10 16 20 25 35 50
Marking:
Capacitor marking will include an anode (+) polarity band, capacitance in microfarads and the voltage rating of + 85C. 'A' Case capacitors use a letter code for the voltage and EIA capacitance code. The Sprague(R) trademark may be included if space permits. Units rated at 6.3 V shall be marked 6 V. A manufacturing date code is marked on all case codes. Call the factory for further explanation.
www.vishay.com 16
For technical questions, contact tantalum@vishay.com
Document Number 40002 Revision 27-Oct-04
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE (F) 3.3 4.7 6.8 10 10 10 15 15 15 22 22 22 22 33 33 33 47 47 68 68 68 100 100 100 150 150 150 220 220 220 330 330 470 470 680 2.2 3.3 3.3 4.7 4.7 6.8 6.8 6.8 10 10 10 15 15 15 22 22 22 33 33 47 47 47 68 68 68 100 100 100 150 150 150 220 220 330 330 470 CASE CODE Max. ESR Max. DC Max. DF @ + 25C Leakage @ + 25C 100kHz @ + 25C 120 Hz PART NUMBER (Ohms) (A) (%) 4 WVDC @ + 85C, SURGE = 5.2 V . . . 2.7 WVDC @ + 125C, SURGE = 3.4 V 0.5 A 6 7.6 293D335X_004A2_E3 0.5 A 6 6.3 293D475X_004A2_E3 0.5 A 6 5.5 293D685X_004A2_E3 0.5 A 6 5.1 293D106X_004A2_E3 0.5 B 6 3.5 293D106X_004B2_E3 0.5 P 6 N/A 293D106X_004P2_E3 0.6 A 6 3.4 293D156X_004A2_E3 0.6 B 6 2.9 293D156X_004B2_E3 0.6 P 6 N/A 293D156X_004P2_E3 0.9 A 6 2.9 293D226X_004A2_E3 0.9 B 6 2.5 293D226X_004B2_E3 0.9 C 6 1.8 293D226X_004C2_E3 0.9 P 6 N/A 293D226X0004P2_E3 1.3 A 6 2.9 293D336X_004A2_E3 1.3 B 6 2.0 293D336X_004B2_E3 1.3 C 6 1.8 293D336X_004C2_E3 1.9 B 6 1.9 293D476X_004B2_E3 1.9 C 6 1.8 293D476X_004C2_E3 2.7 B 6 1.9 293D686X_004B2_E3 2.7 C 6 1.4 293D686X_004C2_E3 2.7 D 6 0.8 293D686X_004D2_E3 4.0 B 8 1.8 293D107X_004B2_E3 4.0 C 6 0.8 293D107X_004C2_E3 4.0 D 6 0.7 293D107X_004D2_E3 6.0 B 14 1.6 293D157X_004B2_E3 6.0 C 12 0.7 293D157X_004C2_E3 6.0 D 8 0.6 293D157X_004D2_E3 8.8 C 8 0.7 293D227X_004C2_E3 8.8 D 8 0.6 293D227X_004D2_E3 8.8 E 8 0.5 293D227X_004E2_E3 13.2 D 8 0.6 293D337X_004D2_E3 13.2 E 8 0.5 293D337X_004E2_E3 18.8 D 10 0.6 293D477X_004D2_E3 18.8 E 10 0.5 293D477X_004E2_E3 27.2 E 12 0.5 293D687X_004E2_E3 6.3 WVDC @ + 85C, SURGE = 8 V . . . 4 WVDC @ + 125C, SURGE = 5 V 7.6 6 293D225X_6R3A2_E3 0.5 A 6.3 6 293D335X_6R3A2_E3 0.5 A N/A 6 293D335X_6R3P2_E3 0.5 P 5.5 293D475X_6R3A2_E3 6 0.5 A N/A 6 293D475X_6R3P2_E3 0.5 P 5.0 293D685X_6R3A2_E3 6 0.5 A 3.4 293D685X_6R3B2_E3 6 0.5 B N/A 293D685X_6R3P2_E3 6 0.5 P 3.4 293D106X_6R3A2_E3 6 0.6 A 2.9 6 293D106X_6R3B2_E3 0.6 B N/A 293D106X_6R3P2_E3 6 0.6 P 2.9 6 293D156X_6R3A2_E3 0.9 A 2.5 6 293D156X_6R3B2_E3 0.9 B 1.8 293D156X_6R3C2_E3 6 0.9 C 2.9 6 293D226X_6R3A2_E3 1.3 A 2.0 6 293D226X_6R3B2_E3 1.3 B 1.8 293D226X_6R3C2_E3 6 1.3 C 1.9 6 293D336X_6R3B2_E3 2.0 B 1.5 6 293D336X_6R3C2_E3 2.0 C 1.9 293D476X_6R3B2_E3 6 2.8 B 1.4 6 293D476X_6R3C2_E3 2.8 C 0.8 6 293D476X_6R3D2_E3 2.8 D 1.8 293D686X_6R3B2_E3 6 4.1 B 0.8 6 293D686X_6R3C2_E3 4.1 C 0.7 6 293D686X_6R3D2_E3 4.1 D 1.7 293D107X_6R3B2_E3 12 6.0 B 0.8 6 293D107X_6R3C2_E3 6.0 C 0.7 6 293D107X_6R3D2_E3 6.0 D 0.7 293D157X_6R3C2_E3 8 9.0 C 0.6 8 293D157X_6R3D2_E3 9.0 D 0.5 8 293D157X_6R3E2_E3 9.0 E 0.6 293D227X_6R3D2_E3 8 13.2 D 0.5 8 293D227X_6R3E2_E3 13.2 E 0.6 8 293D337X_6R3D2_E3 19.8 D 0.5 293D337X_6R3E2_E3 8 19.8 E 0.5 10 293D477X_6R3E2_E3 28.2 E Max. RIPPLE 100kHz Irms (Amps) 0.10 0.11 0.12 0.12 0.16 0.085 0.15 0.17 0.085 0.16 0.18 0.25 0.085 0.16 0.21 0.25 0.21 0.25 0.21 0.28 0.43 0.22 0.37 0.46 0.23 0.40 0.50 0.40 0.50 0.57 0.50 0.57 0.50 0.57 0.57 0.10 0.11 0.085 0.12 0.085 0.12 0.16 0.085 0.15 0.17 0.085 0.16 0.18 0.25 0.16 0.21 0.25 0.21 0.27 0.21 0.28 0.43 0.22 0.37 0.46 0.22 0.37 0.46 0.40 0.50 0.57 0.50 0.57 0.50 0.57 0.57
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
www.vishay.com 17
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE (F) 1.0 1.5 2.2 2.2 3.3 3.3 4.7 4.7 4.7 6.8 6.8 10 10 10 15 15 15 22 22 22 33 33 33 47 47 47 68 68 100 100 150 150 220 220 330 1.0 1.0 1.5 2.2 2.2 3.3 3.3 4.7 4.7 6.8 6.8 6.8 10 10 10 15 15 22 22 22 33 33 33 47 47 68 100 100 150 Max. ESR Max. DC Max. DF @ + 25C Leakage @ + 25C CASE 100kHz @ + 25C 120 Hz CODE PART NUMBER (Ohms) (A) (%) 10 WVDC @ + 85C, SURGE = 13 V . . . 7 WVDC @ + 125C, SURGE = 8 V 0.5 6 P 293D105X_010P2_E3 N/A 0.5 6 293D155X_010A2_E3 A 8.0 0.5 6 293D225X_010A2_E3 A 6.3 0.5 6 P 293D225X_010P2_E3 N/A 0.5 6 293D335X_010A2_E3 A 5.5 0.5 6 293D335X_010P2_E3 P N/A 0.5 6 293D475X_010A2_E3 A 5.0 0.5 6 293D475X_010B2_E3 B 3.4 0.5 6 293D475X_010P2_E3 P N/A 0.7 6 A 293D685X_010A2_E3 4.2 0.7 6 293D685X_010B2_E3 B 2.9 1.0 6 293D106X_010A2_E3 A 3.4 1.0 6 B 293D106X_010B2_E3 2.5 1.0 6 293D106X_010C2_E3 C 1.8 1.5 6 293D156X_010A2_E3 A 2.9 1.5 6 B 293D156X_010B2_E3 2.0 1.5 6 293D156X_010C2_E3 C 1.8 2.2 8 293D226X_010A2_E3 A 2.5 2.2 6 293D226X_010B2_E3 B 1.9 2.2 6 293D226X_010C2_E3 C 1.5 3.3 6 293D336X_010B2_E3 B 1.9 3.3 6 293D336X_010C2_E3 C 1.4 3.3 6 293D336X_010D2_E3 D 0.8 4.7 6 293D476X_010B2_E3 B 1.8 4.7 6 293D476X_010C2_E3 C 1.1 4.7 6 293D476X_010D2_E3 D 0.7 6.8 6 293D686X_010C2_E3 C 1.0 6.8 6 293D686X_010D2_E3 D 0.7 10 8 293D107X_010C2_E3 C 0.9 10 8 293D107X_010D2_E3 D 0.6 15 8 293D157X_010D2_E3 D 0.6 15 8 293D157X_010E2_E3 E 0.5 22 8 293D227X_010D2_E3 D 0.6 22 8 293D227X_010E2_E3 E 0.5 33 10 293D337X_010E2_E3 0.5 E 16 WVDC @ + 85C, SURGE = 20 V . . . 10 WVDC @ + 125C, SURGE = 12 V A P A A B A B A B A B C A B C B C B C D B C D C D D D E E 293D105X_016A2_E3 293D105X_016P2_E3 293D155X_016A2_E3 293D225X_016A2_E3 293D225X_016B2_E3 293D335X_016A2_E3 293D335X_016B2_E3 293D475X_016A2_E3 293D475X_016B2_E3 293D685X_016A2_E3 293D685X_016B2_E3 293D685X_016C2_E3 293D106X_016A2_E3 293D106X_016B2_E3 293D106X_016C2_E3 293D156X_016B2_E3 293D156X_016C2_E3 293D226X0016B2_E3 293D226X_016C2_E3 293D226X_016D2_E3 293D336X0016B2_E3 293D336X_016C2_E3 293D336X_016D2_E3 293D476X_016C2_E3 293D476X_016D2_E3 293D686X_016D2_E3 293D107X_016D2_E3 293D107X_016E2_E3 293D157X_016E2_E3 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.8 1.1 1.1 1.1 1.6 1.6 1.6 2.4 2.4 3.5 3.5 3.5 5.3 5.3 5.3 7.5 7.5 10.9 16 16 24 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 9.3 N/A 6.7 5.9 4.6 5.0 3.5 5.0 2.9 4.2 2.5 1.9 3.0 2.0 1.8 2.0 1.5 1.9 1.4 0.8 1.8 1.1 0.7 1.0 0.7 0.6 0.6 0.6 0.5 Max. RIPPLE 100kHz Irms (Amps) 0.07 0.10 0.11 0.07 0.12 0.07 0.12 0.16 0.07 0.13 0.17 0.15 0.18 0.25 0.16 0.21 0.25 0.17 0.21 0.27 0.21 0.28 0.43 0.22 0.32 0.46 0.33 0.46 0.35 0.50 0.50 0.57 0.50 0.57 0.57 0.09 0.07 0.11 0.11 0.14 0.12 0.16 0.12 0.17 0.13 0.18 0.24 0.16 0.21 0.25 0.21 0.27 0.21 0.28 0.43 0.22 0.32 0.46 0.33 0.46 0.50 0.50 0.52 0.57
*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
www.vishay.com 18
For technical questions, contact tantalum@vishay.com
Document Number 40002 Revision 27-Oct-04
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE (F) CASE CODE PART NUMBER Max. DC Leakage @ + 25C (A) Max. DF @ + 25C 120 Hz (%) Max. ESR @ + 25C 100kHz (Ohms) Max. RIPPLE 100kHz Irms (Amps)
20 WVDC @ + 85C, SURGE = 26 V . . . 13 WVDC @ + 125C, SURGE = 16 V 0.68 1.0 1.5 2.2 2.2 3.3 3.3 4.7 4.7 4.7 6.8 6.8 10 10 15 15 15 22 22 33 33 47 47 68 68 100 A A A A B A B A B C B C B C B C D C D C D D E D E E 293D684X_020A2_E3 293D105X_020A2_E3 293D155X_020A2_E3 293D225X_020A2_E3 293D225X_020B2_E3 293D335X_020A2_E3 293D335X_020B2_E3 293D475X_020A2_E3 293D475X_020B2_E3 293D475X_020C2_E3 293D685X_020B2_E3 293D685X_020C2_E3 293D106X_020B2_E3 293D106X_020C2_E3 293D156X_020B2_E3 293D156X_020C2_E3 293D156X_020D2_E3 293D226X_020C2_E3 293D226X_020D2_E3 293D336X_020C2_E3 293D336X_020D2_E3 293D476X_020D2_E3 293D476X_020E2_E3 293D686X_020D2_E3 293D686X_020E2_E3 293D107X_020E2_E3 0.5 0.5 0.5 0.5 0.5 0.7 0.7 0.9 0.9 0.9 1.4 1.4 2.0 2.0 3.0 3.0 3.0 4.4 4.4 6.6 6.6 9.4 9.4 13.6 13.6 20.0 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 10 8.4 6.3 5.9 3.5 5.9 3.0 5.0 2.9 2.3 2.5 1.9 2.5 1.7 2.3 1.5 0.9 1.1 0.7 1.0 0.7 0.7 0.6 0.7 0.6 0.5 0.09 0.09 0.11 0.11 0.16 0.11 0.17 0.12 0.17 0.22 0.18 0.24 0.18 0.25 0.19 0.27 0.41 0.32 0.46 0.33 0.46 0.46 0.52 0.46 0.52 0.57
25 WVDC @ + 85C, SURGE = 32 V . . . 17 WVDC @ + 125C, SURGE = 20 V 0.47 0.68 1.0 1.0 1.5 1.5 2.2 2.2 3.3 3.3 4.7 4.7 6.8 6.8 10 10 15 15 22 33 33 A A A B A B A B B C B C B C C D C D D D E 293D474X_025A2_E3 293D684X_025A2_E3 293D105X_025A2_E3 293D105X_025B2_E3 293D155X_025A2_E3 293D155X_025B2_E3 293D225X_025A2_E3 293D225X_025B2_E3 293D335X_025B2_E3 293D335X_025C2_E3 293D475X_025B2_E3 293D475X_025C2_E3 293D685X_025B2_E3 293D685X_025C2_E3 293D106X_025C2_E3 293D106X_025D2_E3 293D156X_025C2_E3 293D156X_025D2_E3 293D226X_025D2_E3 293D336X_025D2_E3 293D336X_025E2_E3 0.5 0.5 0.5 0.5 0.5 0.5 0.6 0.6 0.8 0.8 1.2 1.2 1.7 1.7 2.5 2.5 3.8 3.8 5.5 8.3 8.3 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 12 8.4 7.6 5.0 6.7 4.6 6.3 3.8 3.1 2.3 2.8 2.0 2.4 1.7 1.5 1.0 1.2 0.8 0.7 0.7 0.6 0.08 0.09 0.10 0.13 0.11 0.14 0.11 0.15 0.17 0.22 0.17 0.24 0.19 0.25 0.27 0.39 0.30 0.43 0.46 0.46 0.52
**Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
www.vishay.com 19
293D
Vishay Sprague
STANDARD/EXTENDED RATINGS
CAPACITANCE (F) CASE CODE Max. DC Leakage @ + 25C (A) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 0.8 1.2 1.2 1.6 1.6 2.4 2.4 3.5 3.5 5.3 5.3 7.7 7.7 Max. DF @ + 25C 120 Hz (%) 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Max. ESR @ + 25C 100kHz (Ohms) 20 18 15 13 10 8 7.6 6.5 7.5 5.0 4.2 3.8 3.8 2.9 3.5 2.1 1.9 1.3 1.8 1.1 0.7 0.8 0.7 0.7 0.6 0.6 Max. RIPPLE 100kHz Irms (Amps) 0.06 0.07 0.07 0.08 0.09 0.10 0.10 0.11 0.10 0.13 0.14 0.17 0.15 0.20 0.16 0.23 0.24 0.34 0.25 0.37 0.46 0.43 0.46 0.49 0.52 0.52 0.06 0.07 0.08 0.07 0.08 0.07 0.09 0.08 0.10 0.13 0.11 0.14 0.11 0.16 0.18 0.20 0.27 0.21 0.30 0.37 0.41 0.43 0.43 0.45
PART NUMBER
35 WVDC @ + 85C, SURGE = 46 V . . . 23 WVDC @ + 125C, SURGE = 28 V 0.10 0.15 0.22 0.33 0.47 0.47 0.68 0.68 1.0 1.0 1.5 1.5 2.2 2.2 3.3 3.3 4.7 4.7 6.8 6.8 10 10 15 15 22 22 A A A A A B A B A B B C B C B C C D C D C D D E D E 293D104X_035A2_E3 293D154X_035A2_E3 293D224X_035A2_E3 293D334X_035A2_E3 293D474X_035A2_E3 293D474X_035B2_E3 293D684X_035A2_E3 293D684X_035B2_E3 293D105X_035A2_E3 293D105X_035B2_E3 293D155X_035B2_E3 293D155X_035C2_E3 293D225X_035B2_E3 293D225X_035C2_E3 293D335X_035B2_E3 293D335X_035C2_E3 293D475X_035C2_E3 293D475X_035D2_E3 293D685X_035C2_E3 293D685X_035D2_E3 293D106X_035D2_E3 293D106X_035D2_E3 293D156X_035D2_E3 293D156X_035E2_E3 293D226X_035D2_E3 293D226X_035E2_E3
50 WVDC @ + 85C, SURGE = 65 V . . . 33 WVDC @ + 125C, SURGE = 40 V 0.10 0.15 0.15 0.22 0.22 0.33 0.33 0.47 0.47 0.47 0.68 0.68 1.0 1.0 1.5 2.2 2.2 3.3 3.3 4.7 6.8 6.8 10 10 A A B A B A B A B C B C B C C C D C D D D E D E 293D104X_050A2_E3 293D154X_050A2_E3 293D154X_050B2_E3 293D224X_050A2_E3 293D224X_050B2_E3 293D334X_050A2_E3 293D334X_050B2_E3 293D474X_050A2_E3 293D474X_050B2_E3 293D474X_050C2_E3 293D684X_050B2_E3 293D684X_050C2_E3 293D105X_050B2_E3 293D105X_050C2_E3 293D155X_050C2_E3 293D225X_050C2_E3 293D225X_050D2_E3 293D335X_050C2_E3 293D335X_050D2_E3 293D475X_050D2_E3 293D685X_050D2_E3 293D685X_050E2_E3 293D106X_050D2_E3 293D106X_050E2_E3 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 1.1 1.1 1.7 1.7 2.4 3.4 3.4 5.0 5.0 4 4 4 4 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 19 17 14 15 12 14 10 12 8.4 6.7 7.6 5.9 6.7 4.6 3.4 2.9 2.1 2.5 1.7 1.2 0.9 0.9 0.8 0.8
**Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print.
www.vishay.com 20
For technical questions, contact tantalum@vishay.com
Document Number 40002 Revision 27-Oct-04
293D
Vishay Sprague
TYPICAL CURVES @ + 25C, IMPEDANCE AND ESR
VS
FREQUENCY
100 IMPEDANCE ESR 10
OHMS OHMS
100 IMPEDANCE ESR 10
4.7F, 10VDC-B CASE 1 47F, 10VDC-D CASE
10F, 16VDC-C CASE 1
0.1 1K 10K 100K 1M 10M 100M FREQUENCY IN HERTZ
0.1 1K 10K 100K 1M 10M 100M FREQUENCY IN HERTZ
100 IMPEDANCE ESR 10
OHMS OHMS
100 IMPEDANCE ESR 10
1F, 35VDC-B CASE 1 6.8F, 35VDC-D CASE
6.8F, 20VDC-C CASE 1 22F, 20VDC-D CASE
0.1 1K 10K 100K 1M 10M 100M FREQUENCY IN HERTZ
0.1 1K 10K 100K 1M 10M 100M FREQUENCY IN HERTZ
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
www.vishay.com 21
293D
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1. 1.1 Operating Temperature: Capacitors are designed to operate over the temperature range - 55C to + 85C. Capacitors may be operated to + 125C with voltage derating to two-thirds the + 85C rating.
+ 85C Rating Working Voltage (V) 4 6.3 10 16 20 25 35 50 Surge Voltage (V) 5.2 8 13 20 26 32 46 65 + 125C Rating Working Voltage (V) 2.7 4 7 10 13 17 23 33 Surge Voltage (V) 3.4 5 8 12 16 20 28 40
5.
Capacitance Change With Temperature: The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25C:
- 55C - 10%
+ 85C + 10%
+ 125C + 12%
6.
Dissipation Factor: The dissipation factor, determined from the expression 2fRC, shall not exceed values listed in the Standard Ratings Table. Measurements shall be made by the bridge method at, or referred to, a frequency of 120 Hz and a temperature of + 25C. Leakage Current: Capacitors shall be stabilized at the rated temperature for 30 minutes. Rated voltage shall be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with 1000 ohm resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall then be measured.
6.1
7. 2. DC Working Voltage: The DC working voltage is the maximum operating voltage for continuous duty at the rated temperature. 3. Surge Voltage: The surge DC rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage. 3.1 Surge Voltage Test: Capacitors shall withstand the surge voltage applied in series with a 33 ohm 5% resistor at the rate of one-half minute on, one-half minute off, at + 85C, for 1000 successive test cycles.
Note that the leakage current varies with temperature and applied voltage. See graph below for the appropriate adjustment factor.
TYPICAL LEAKAGE CURRENT FACTOR RANGE
100
+ 125C + 85C 10
3.2
Following the surge voltage test, the dissipation factor and the leakage current shall meet the initial requirements; the capacitance shall not have changed
Leakage Current Factor
+ 55C
+ 25C 1.0 0C
more than 10%. 4. Capacitance Tolerance: The capacitance of all capacitors shall be within the specified tolerance limits of the normal rating. 4.1 Capacitance measurements shall be made by means of polarized capacitance bridge. The polarizing voltage shall be of such magnitude that there shall be no reversal of polarity due to the AC component. The maximum voltage applied to capacitors during measurement shall be 2 volts rms at 120 Hz at +25C. If the AC voltage applied is less than one-half volt rms, no DC bias is required. Accuracy of the bridge shall be within 2%.
www.vishay.com 22
0.1 - 55C
0.01
0.001 0 10 20 30 40 50 60 70 80 90 100 Percent of Rated Voltage
For technical questions, contact tantalum@vishay.com
Document Number 40002 Revision 27-Oct-04
293D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
7.1 7.2 7.3 At + 25C, the leakage current shall not exceed the value listed in the Standard Ratings Table. At + 85C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings Table. At + 125C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings Table. ESR ESR (Equivalent Series Resistance) shall not exceed the values listed in the Ratings Table. Measurement shall be made by the bridge method at a frequency of 100kHz and a temperature of +25C. Life Test: Capacitors shall withstand rated DC voltage applied at + 85C or two-thirds rated voltage applied at + 125C for 2000 hours. Following the life test, the dissipation factor shall meet the initial requirement; the capacitance change shall not exceed 10%; the leakage current shall not exceed 125% of the initial requirement. Vibration Tests: Capacitors shall be subjected to vibration tests in accordance with the following criteria. Capacitors shall be secured for test by means of a rigid mounting using suitable brackets. Low Frequency Vibration: Vibration shall consist of simple harmonic motion having an amplitude of 0.03" [0.76mm] and a maximum total excursion of 0.06" [1.52mm], in a direction perpendicular to the major axis of the capacitors. 0.06" [1.52] 10% maximum total excursion or 20 g peak whichever is less. 10.3.1 Vibration frequency shall be varied logarithmically from 50 Hz to 2000 Hz and return to 50 Hz during a cycle period of 20 minutes. 10.3.2 The vibration shall be applied for 4 hours in each of 2 directions, parallel and perpendicular to the major axis of the capacitors. 10.3.3 Rated DC voltage shall be applied during the vibration cycling. 10.3.4 An oscilloscope or other comparable means shall be used in determining electrical intermittency during the last cycle. The AC voltage applied shall not exceed 2 volts rms. 10.3.5 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 10.3.6 There shall be no mechanical damage to these capacitors as a result of these tests. 10.3.7 Following the high frequency vibration test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current. 11. 11.1 11.2 Acceleration Test: Capacitors shall be rigidly mounted by means of suitable brackets. Capacitors shall be subjected to a constant acceleration of 100 g for a period of 10 seconds in each of 2 mutually perpendicular planes.
8. 8.1
9.
9.1
10. 10.1 10.2
10.2.1 Vibration frequency shall be varied uniformly between the approximate limits of 10 Hz to 55 Hz during a period of approximately one minute, continuously for 1.5 hours. 10.2.2 An oscilloscope or other comparable means shall be used in determining electrical intermittency during the final 30 minutes of the test. The AC voltage applied shall not exceed 2 volts rms. 10.2.3 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 10.2.4 Following the low frequency vibration test, capacitors shall meet the original requirements for capacitance, dissipation factor and leakage current. 10.3 High Frequency Vibration: Vibration shall consist of a simple harmonic motion having an amplitude of
11.2.1 The direction of motion shall be parallel to and perpendicular to the longitudinal axis of the capacitors. 11.3 Rated DC voltage shall be applied during acceleration test.
11.3.1 An oscilloscope or other comparable means shall be used in determining electrical intermittency during test. The AC voltage applied shall not exceed 2 volts rms. 11.4 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. There shall be no mechancial damage to these capacitors as a result of these tests. Following the acceleration test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current.
11.5 11.6
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
www.vishay.com 23
293D
Vishay Sprague
PERFORMANCE CHARACTERISTICS (Continued)
12. 12.1 Shock Test: 14.3 Capacitors shall be rigidly mounted by means of suitable brackets. The test load shall be distributed uniformly on the test platform to minimize the effects of unbalanced loads. 12.1.1 Test equipment shall be adjusted to produce a shock of 100 g peak with the duration of 6 mS and sawtooth waveform at a velocity change of 9.7 ft./sec. 12.2 Capacitors shall be subjected to 3 shocks applied in each of 3 directions corresponding to the 3 mutually perpendicular axes of the capacitors. Rated DC voltage shall be applied during test. + 125C (+ 3C, - 0C) for 30 minutes, then + 25C (+ 10C, - 5C) for 5 minutes for 5 cycles. Capacitors shall show no evidence of harmful or extensive corrosion, obliteration of marking or other visible damage. Following the thermal shock test, capacitors shall meet the original requirements for leakage current and dissipation factor. Capacitance change shall not exceed 5% of the original measured value. Soldering Compatibility: Resistance to Solder Heat: Capacitors will withstand exposure to + 260C + 5C for 10 seconds.
14.4
15. 15.1
12.3
12.3.1 An oscilloscope or other comparable means shall be used in determining electrical intermittency during tests. The replacement voltage applied shall not exceed 2 volts rms. 12.4 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. There shall be no mechanical damage to these capacitors as a result of these tests. Following the shock test, capacitors shall meet the original limits for capacitance, dissipation factor and l leakage current. Moisture Resistance: Capacitors shall be subjected to temperature cycling at 90% to 95% relative humidity, from + 25C to +65C to + 25C (+ 10C, - 2C) over a period of 8 hours per cycle for 1000 hours. Following the moisture resistance test, the leakage current and dissipation factor shall meet the initial requirements, and the change in capacitance shall not exceed 10%. Thermal Shock: Capacitors shall be conditioned prior to temperature cycling for 15 minutes at + 25C, at less than 50% relative humidity and a barometric pressure at 28 to 31" Capacitors shall be subjected to thermal shock in a cycle of exposure to ambient air at : - 55C (+ 0C,- 5C) for 30 minutes, then + 25C (+10C, - 5C) for 5 minutes, then
15.1.1 Following the resistance to soldering heat test, capacitance, dissipation factor and DC leakage current shall meet the initial requirement. 15.2 Solderability: Capacitors will meet the solderability requirements of ANSI/J-STD-002, Test B (MIL-STD202, method and test S.) Terminal Strength: Per UEC-384-3, minimum of 5N shear force. Environmental: Mercury, CFC and ODS materials are not used in the manufacture of these capacitors. Flammability: Encapsulant materials meet UL94 V0 with an oxygen index of 32%. Capacitor Failure Mode: The predominant failure mode for solid tantalum capacitors is increased leakage current resulting in a shorted circuit. Capacitor failure may result from excess forward or reverse DC voltage, surge current, ripple current, thermal shock or excessive temperature. The increase in leakage is caused by a breakdown of the Ta2O5 dielectric. For additional information on leakage failure of solid tantalum chip capacitors, refer to Vishay Sprague Technical Paper, "Leakage Failure Mode in Solid Tantalum Chip Capacitors." 20. Surge Current: All D and E case code 293D capacitors are 100% surge current tested at + 25C and rated voltage. The total series circuit resistance is 0.5 ohms. Each charge cycle of 0.10 seconds is followed by a discharge cycle of 0.10 seconds. Three surge cycles are applied. Each capacitor is tested individually to maximize the peak charging current.
Document Number 40002 Revision 27-Oct-04
16.
12.5
17.
12.6
18.
13. 13.1
19.
13.2
14. 14.1
14.2
www.vishay.com 24
For technical questions, contact tantalum@vishay.com
293D
Vishay Sprague
GUIDE TO APPLICATION
1. A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: P RESR important that the equivalent Irms value be established when calculating permissible operating levels. (Power Dissipation calculated using + 25C temperature rise.)
Maximum Permissible Power Dissipation @ + 25C (Watts) in free air 0.075 0.085 0.110 0.150 0.165 0.025
Irms = where,
Case Code A B C D E P
P = Power Dissipation in Watts @ + 25C as given in the table in Paragraph Number 5 (Power Dissipation). RESR = The capacitor Equivalent Series Resistance at the specified frequency. 2. A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: Vrms = Z or, from the formula: Vrms = Irms x Z where, P = Power Dissipation in Watts @ + 25C as given in the table in Paragraph Number 5 (Power Dissipation). 7.1 P RESR 7.
6.
Printed Circuit Board Materials: Type 293D capacitors are compatible with commonly used printed circuit board materials (alumina substrates, FR4, FR5, G10, PTFE-fluorocarbon and porcelanized steel). Attachment: Solder Paste: The recommended thickness of the solder paste after application is .007" .001" [.178mm .025mm]. Care should be exercised in selecting the solder paste. The metal purity should be as high as practical. The flux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the exposure to soldering heat. In practice this can be aided by extending the solder preheat time at temperatures below the liquidous state of the solder. Soldering: Capacitors can be attached by conventional soldering techniques - vapor phase, infrared reflow, wave soldering and hot plate methods. The Soldering Profile chart shows maximum recomended time/temperature conditions for soldering. Attachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at temperature. Cleaning (Flux Removal) After Soldering: The 293D is compatible with all commonly used solvents such as TES, TMS, Prelete, Chlorethane, Terpene and aqueous cleaning media. However, CFC/ODS products are not used in the production of these devices and are not recommended. Solvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. When using ultrasonic cleaning, the board may resonate if the output power is too high. This vibration can cause cracking or a decrease in the adherence of the termination. DO NOT EXCEED 9W/l @ 40kHz for 2 minutes.
RESR = The capacitor Equivalent Series Resistance at the specified frequency. Z 2.1 = The capacitor impedance at the specified frequency.
The sum of the peak AC voltage plus the DC voltage shall not exceed the DC voltage rating of the capacitor. The sum of the negative peak AC voltage plus the applied DC voltage shall not allow a voltage reversal exceeding 10% of the DC rating at + 25C. Reverse Voltage: These capacitors are capable of withstanding peak voltages in the reverse direction equal to 10% of the DC rating at + 25C, 5% of the DC rating at + 85C and 1% of the DC rating at +125C. Temperature Derating: If these capacitors are to be operated at temperatures above + 25C, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown:
Temperature + 25C + 85C + 125C Derating Factor 1.0 0.9 0.4
7.2
2.2
3.
8.
4.
8.1
5.
Power Dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
www.vishay.com 25
293D
Vishay Sprague
GUIDE TO APPLICATION (Continued) SOLDERING PROFILE
Recommended Solder Profile -- Wave Solder
5 - 10 Sec.
Recommended Solder Profile -- Reflow
Temperature Degrees Centigrade
300
300 245C Typical 250 200 130C Typical 150 100 50 0 0 50 100 150 200 250
Temperature Degrees Centigrade
300 250 200 150 100 50 0 0
Max. Recommended 260C
300 250 200
250 200 150 100 50 0
130C
150 100 50 0
50
100
150
200
250
Time (Seconds)
Time (Seconds)
9.
Recommended Mounting Pad Geometries: Proper mounting pad geometries are essential for successful solder connections. These dimensions are highly process sensitive and should be designed to minimize component rework due to unacceptable solder joints. The dimensional configurations shown are the recommended pad geometries for both wave and reflow soldering techniques. These dimensions are intended to be a starting point for circuit board designers and may be fine tuned if necessary based upon the peculiarities of the soldering process and/or circuit board design.
RECOMMENDED MOUNTING PAD GEOMETRIES in inches [millimeters]
Wave Solder Pads
D B C E B
Reflow Solder Pads
D C E
A
A
Pad Dimensions
Pad Dimensions
Case Code A B C D E P
A (Min.) 0.034 [0.87] 0.061 [1.54] 0.061 [1.54] 0.066 [1.68] 0.066 [1.68] 0.034 [0.87]
B (Nom.) 0.085 [2.15] 0.085 [2.15] 0.106 [2.70] 0.106 [2.70] 0.106 [2.70] 0.085 [2.15]
C (Nom.) 0.053 [1.35] 0.065 [1.65] 0.124 [3.15] 0.175 [4.45] 0.175 [4.45] 0.053 [1.35]
D (Nom.) 0.222 [5.65] 0.234 [5.95] 0.337 [8.55] 0.388 [9.85] 0.388 [9.85] 0.222 [5.65]
E (Nom.) 0.048 [1.23] 0.048 [1.23] 0.050 [1.28] 0.050 [1.28] 0.050 [1.28] 0.048 [1.23]
Case Code A B C D E P
A (Min.) 0.071 [1.80] 0.110 [2.80] 0.110 [2.80] 0.118 [3.00] 0.118 [3.00] 0.071 [1.80]
B (Nom.) 0.085 [2.15] 0.085 [2.15] 0.106 [2.70] 0.106 [2.70] 0.106 [2.70] 0.085 [2.15]
C (Nom.) 0.053 [1.35] 0.065 [1.65] 0.124 [3.15] 0.175 [4.45] 0.175 [4.45] 0.053 [1.35]
D (Nom.) 0.222 [5.65] 0.234 [5.95] 0.337 [8.55] 0.388 [9.85] 0.388 [9.85] 0.222 [5.65]
E (Nom.) 0.048 [1.23] 0.048 [1.23] 0.050 [1.28] 0.050 [1.28] 0.050 [1.28] 0.048 [1.23]
www.vishay.com 26
For technical questions, contact tantalum@vishay.com
Document Number 40002 Revision 27-Oct-04
293D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
.157 .004 [4.0 .10] K Max. .024 [.600] Max. .059 + .004 - 0.0 [1.5 + .10 - 0.0] .069 .004 [1.75 .10]
.079 .002 [2.0 .050]
A0
F W
B0 B1 Max. K0 P Top Cover Tape Direction of Feed D1 Min.
TAPE SIZE B1 (Max.) D1 (Min.) 8mm 12mm 0.165 [4.2] 0.323 [8.2] 0.039 [1.0] 0.059 [1.5]
F 0.138 0.002 [3.5 0.05] 0.217 0.002 [5.5 0.05]
K (Max.) 0.094 [2.4] 0.177 [4.5]
A0B0K0 Notes: A0B0K0 are determined by component size. 0.157 0.004 0.315 0.012 The clearance between the component and the [4.0 1.0] [8.0 0.30] cavity must be within 0.002" [0.05mm] minimum to 0.315 0.004 0.472 0.012 0.020" [0.50mm] maximum for 8mm tape and 0.002" [8.0 1.0] [12.0 0.30] [0.05mm] minimum to 0.026" [0.65mm] maximum for 12mm tape. W
P
Standard orientation is with the cathode (-) nearest to the sprocket holes per EIA-481-1 and IEC 286-3. Top Cover Tape Thickness
Tape and Reel Specifications: All case codes are available on plastic embossed tape per EIA-481-1. Tape reeling per IEC 286-3 is also available. Standard reel diameter is 13" [330mm]. 7" [178mm] reels are available. The most efficient packaging quantities are full reel increments on a given reel diameter. The quantities shown allow for the sealed empty pockets required to be in conformance with EIA-481-1. Reel size must be specified in the Vishay Sprague part number.
Carrier Embossment
Units Per Reel
Cathode (-)
Case Code A B C D E P
Tape Width 8mm 8mm 12mm 12mm 12mm 8mm
Component 7" [178mm] 13" [330mm] Reel Reel Pitch 4mm 4mm 8mm 8mm 8mm 4mm 2000 2000 500 500 400 3000 9000 8000 3000 2500 1500 10000
Anode (+) Direction of Feed
Document Number 40002 Revision 27-Oct-04
For technical questions, contact tantalum@vishay.com
www.vishay.com 27

▲Up To Search▲

Price & Availability of 293D107X0010D2T

	To Download 293D107X0010D2T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .